: The coremod requested minecraft version 1.10.2 and minecraft is 1.10.2. : Found FMLCorePluginContainsFMLMod marker in AppleCore-mc1.10.2-2.1.0.jar, it will be examined later for regular instances : Examining for coremod candidacy AppleCore-mc1.10.2-2.1.0.jar : Not found coremod data in actuallycomputers-0.1.0.jar : Examining for coremod candidacy actuallycomputers-0.1.0.jar : Not found coremod data in ActuallyAdditions-1.10.2-r94.jar : Examining for coremod candidacy ActuallyAdditions-1.10.2-r94.jar : Not found coremod data in BetterCombatMod 1.3.5.jar : Examining for coremod candidacy BetterCombatMod 1.3.5.jar : Not found coremod data in FenceOverhaul-1.2.1.jar : Examining for coremod candidacy FenceOverhaul-1.2.1.jar : Attempting to load commandline specified mods, relative to C:\server\. : All fundamental core mods are successfully located : Instantiating coremod class FMLForgePlugin : Added access transformer class. to enqueued access transformers : Instantiating coremod class FMLCorePlugin : Java library path at launch is C:\ProgramData\Oracle\Java\javapath C:\WINDOWS\Sun\Java\bin C:\WINDOWS\system32 C:\WINDOWS C:\ProgramData\Oracle\Java\javapath C:\Program Files (x86)\Intel\iCLS Client\ C:\Program Files\Intel\iCLS Client\ C:\WINDOWS\system32 C:\WINDOWS C:\WINDOWS\System32\Wbem C:\WINDOWS\System32\WindowsPowerShell\v1.0\ C:\Program Files (x86)\Skype\Phone\ C:\Program Files (x86)\Intel\Intel(R) Management Engine Components\DAL C:\Program Files\Intel\Intel(R) Management Engine Components\DAL C:\Program Files (x86)\Intel\Intel(R) Management Engine Components\IPT C:\Program Files\Intel\Intel(R) Management Engine Components\IPT C:\Program Files (x86)\QuickTime\QTSystem\ C:\Users\wiola\AppData\Local\Microsoft\WindowsApps. : Java classpath at launch is FTBserver-1.10. : Java is Java HotSpot(TM) 64-Bit Server VM, version 1.8.0_121, running on Windows 10:amd64:10.0, installed at C:\Program Files\Java\jre1.8.0_121 You have to check and change the addresses each time you make a new setup somewhere else.: Injecting tracing printstreams for STDOUT/STDERR. Note: Each adapter in the world has a different address aka you cant copy paste your harddrive in another setup and hope it works. When it's done charging, press the activate button and you're all set! Then, run the two commands "draconic_control start" and afterwards, "dc_gui"įinally, Hit the charge button in the reactor's stabilizer GUI enable fail-safe mode aswell. Press "Ctrl + S" to save the file and "Ctrl + W" to exit. Replace the ZZZZ, also denoted as the fluxGateOutputAddress with the address produced by the adapter next to the Flux Gate attached to the stabilizer. Replace the YYYY, also denoted as the fluxGateDrainbanAddress with the address produced by the adapter next to the Flux Gate attached to the Reactor Energy Injector. Replace the XXXX, also denoted as the reactorAddress with the address produced by the adapter next to the Stabilizer. Grab an analyzer and shift click on the three adapters, they should give you the addresses of the block such as this:Ĭlick on your monitor again and remember the middle-mouse paste trick. For now just hit Escape to exit the screen. You will have to change this to the actual address of the components. Type in "edit /etc/draconic_control.cfg and you'll see that the addresses are filled in with temporary XXXX, YYYY and ZZZZ's. This will install the file in the /etc/ directory which is required. Paste in the command "pastebin get mv2QEQHx /etc/draconic_control.cfg". This will install the lua file and it's necessary components. Type the command "wget ". You can copy this and press middle mouse-click inside your monitor GUI to paste the command. (Type in Y if it asks for Y/n questions). You will have to install the OpenOS software first. Okay so after you have pressed the power on button, you'll have to follow the following steps on your monitor (Right click it to access):Įxecute "install" in your monitor.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |